I just swapped over to GP shift and wanted to share my experience and detail it for anyone else who is looking to do this . Enjoy !
***********************************************************
*****Disclaimer: I do not claim to be an motorcycle expert in any way shape or form. This is my experience as a self taught bike mechanic and do not take responsibility for any mistakes that may happen or any injuries that may be caused by anyone following this post... Proceed at your own risk. *****************************************************
Tools needed: set of metric Allen’s 3/4/5/6, Locktite green and red, 12mm &10mm wrench . Rear stand or a friend to help hold the bike as you will need to have the kickstand up to remove the body work. And a blanket to put your body work on so it doesn’t get scratched up.
Step 1. Put bike on rear stand and pick up kickstand. This is where that friend would come into play if you don’t have a rear stand .
Step 2. Remove the lower left side belly pan by rearset(shifter side). This is a total of about 8 size 3 hex head screws four in the bottom of the belly pan underneath the bike and 4 in the bottom side of the bike. Two of them I believe were size 4. There’s a breather tube that you will have to disconnect to fully remove the side of the belly pan after all the allens are removed. Remove lower and set aside on blanket
Step 3. Remove top bolt on rearset. 6mm (I believe )
And then remove side bolt on rearset (same size)
At this point you need to remove the other bolt where the quick shifter attaches to the bike.
Step 4. Brake loose the eye socket from the quick shifter using a 12&10mm wrench . Once loose you should be able to unthread the rear set completely from the quickshifter. Make sure to mark the threads showing on the eye socket end so when you retighten them they are the same length. Mine had 6 threads showing so I would assume they all should .
At this point you need to remove the other bolt where the quick shifter rod is attached to the bike.
Step 5. Remove Allen bolt from eye socket using 4mm Allen from toe peddle assembly. Take caution when doing this as this Allen is locktited in and is very easily stripped. Unfortunately I found out the hard way. I put the assembly carefully in a vice so I could remove the Allen bolt from the eye socket.
Step 6. Transfer eye socket to lower pretapped hole on bottom of toe peddle and retighten Allen bolt making sure to reapply green locktite .
Step 7. Reinstall rear set side bolt leaving the bolt slightly loose, then reinstall top bolt and fully tighten Allen bolt and then fully tighten side Allen bolt.
Step 8. Attach eye socket back to quick shifter rod and leave slightly loose . Then attach other end (left side when looking at the bike) of quick shifter back to the bike . This is also an eye socket and will require red locktite. Afterwards fully tighten other side of quick shift rod to eye socket using 10&12mm wrench making sure you have your 6 threads showing on eye socket side when fully tightened back to quick shifter rod .
Step 9. Start bike and test shifter to make sure you get all six gears and the bike is shifting smoothly and easily. I did this while the bike was on the rear stand. You could always test ride as well. You choose.
Step 10. Re-install lower side fairing/belly pan making sure you attach the black breather hose back in its position before you put the bodywork back in place .
Step 11. Pat yourself on the back and rejoice in the $150 plus dollars you just saved yourself by not going to the dealer to have this done, shake hands with Mary Jane and go ride your newly transformed GP shift panigale v4s. Not necessarily in that order.
Enjoy! 🇮🇹
***********************************************************
*****Disclaimer: I do not claim to be an motorcycle expert in any way shape or form. This is my experience as a self taught bike mechanic and do not take responsibility for any mistakes that may happen or any injuries that may be caused by anyone following this post... Proceed at your own risk. *****************************************************
Tools needed: set of metric Allen’s 3/4/5/6, Locktite green and red, 12mm &10mm wrench . Rear stand or a friend to help hold the bike as you will need to have the kickstand up to remove the body work. And a blanket to put your body work on so it doesn’t get scratched up.
Step 1. Put bike on rear stand and pick up kickstand. This is where that friend would come into play if you don’t have a rear stand .
Step 2. Remove the lower left side belly pan by rearset(shifter side). This is a total of about 8 size 3 hex head screws four in the bottom of the belly pan underneath the bike and 4 in the bottom side of the bike. Two of them I believe were size 4. There’s a breather tube that you will have to disconnect to fully remove the side of the belly pan after all the allens are removed. Remove lower and set aside on blanket
Step 3. Remove top bolt on rearset. 6mm (I believe )
And then remove side bolt on rearset (same size)
At this point you need to remove the other bolt where the quick shifter attaches to the bike.
Step 4. Brake loose the eye socket from the quick shifter using a 12&10mm wrench . Once loose you should be able to unthread the rear set completely from the quickshifter. Make sure to mark the threads showing on the eye socket end so when you retighten them they are the same length. Mine had 6 threads showing so I would assume they all should .
At this point you need to remove the other bolt where the quick shifter rod is attached to the bike.
Step 5. Remove Allen bolt from eye socket using 4mm Allen from toe peddle assembly. Take caution when doing this as this Allen is locktited in and is very easily stripped. Unfortunately I found out the hard way. I put the assembly carefully in a vice so I could remove the Allen bolt from the eye socket.
Step 6. Transfer eye socket to lower pretapped hole on bottom of toe peddle and retighten Allen bolt making sure to reapply green locktite .
Step 7. Reinstall rear set side bolt leaving the bolt slightly loose, then reinstall top bolt and fully tighten Allen bolt and then fully tighten side Allen bolt.
Step 8. Attach eye socket back to quick shifter rod and leave slightly loose . Then attach other end (left side when looking at the bike) of quick shifter back to the bike . This is also an eye socket and will require red locktite. Afterwards fully tighten other side of quick shift rod to eye socket using 10&12mm wrench making sure you have your 6 threads showing on eye socket side when fully tightened back to quick shifter rod .
Step 9. Start bike and test shifter to make sure you get all six gears and the bike is shifting smoothly and easily. I did this while the bike was on the rear stand. You could always test ride as well. You choose.
Step 10. Re-install lower side fairing/belly pan making sure you attach the black breather hose back in its position before you put the bodywork back in place .
Step 11. Pat yourself on the back and rejoice in the $150 plus dollars you just saved yourself by not going to the dealer to have this done, shake hands with Mary Jane and go ride your newly transformed GP shift panigale v4s. Not necessarily in that order.
Enjoy! 🇮🇹