remove exup valvle?? - Ducati Panigale V4 Forum
 3Likes
Reply
 
LinkBack Thread Tools
post #1 of 15 (permalink) Old 05-07-2018, 08:25 PM Thread Starter
Junior Member
 
eddyV4's Avatar
 
Join Date: Apr 2018
Posts: 10
remove exup valvle??

hi☺
What do you think about removing the exhaust valve?
in what help?
What affects?
if I remove it from the muffler that I would not touch, none of the 2 metal wires to avoid the fault light will simply remove it from the inside of the muffler and I put a wedge to fool the servo if the fin is acting.
regards ✌

Last edited by eddyV4; 05-07-2018 at 08:30 PM.
eddyV4 is offline  
post #2 of 15 (permalink) Old 08-08-2018, 02:24 PM
Junior Member
 
winnie's Avatar
 
Join Date: May 2018
Location: Germany
Posts: 17
Did anyone know something about an Exhaust-Valve-eliminator??
winnie is offline  
post #3 of 15 (permalink) Old 08-08-2018, 04:17 PM
Member
 
Join Date: Aug 2018
Posts: 54
The valve eliminator still doesn't exist. Patiently waiting on this.
MotomillioN is offline  
post #4 of 15 (permalink) Old 08-09-2018, 10:49 AM
Junior Member
 
Join Date: Jul 2018
Posts: 28
you can remove the valve and just undo the cables from the servo and it should not throw any codes as the servo will continue to act as normal, only its not manipulating the valve, at least this is what i have read elsewhere and possibly about the previous 1X99,

as for the valve itself I am not sure how to get to it as I have not messed with the one on my bike as I am planning on making my own slipons this winter and don't care that the valve is there, but you should be able to rip/cut the valve out and replace it with a nut and bolt through the left over hole or what some did on the 1X99 was just drill the rivets out of the flapper piece and the arm that it was riveted to... but again i have not really looked into this exhaust..

But I would not undo the cables from the servo motor unless you have removed the valve as the valve is most likely spring closed and it would be closed at all times which is not good..

someone please correct me if I m wrong or misleading here..
CRAZYDUC996 is offline  
post #5 of 15 (permalink) Old 08-09-2018, 11:24 AM
Junior Member
 
winnie's Avatar
 
Join Date: May 2018
Location: Germany
Posts: 17
Normaly the valve is open the whole time,closed only in a small section of Rpm.
At the 1299 it has sometimes happend,that the valvespring is not strong enough to keep the valve open...
You couldnt see an error in the display when the cables are taken away,but there is an errorcode in the controlmodul...
winnie is offline  
post #6 of 15 (permalink) Old 08-16-2018, 02:21 PM
Member
 
Join Date: Aug 2018
Posts: 54
Quote:
Originally Posted by CRAZYDUC996 View Post
you can remove the valve and just undo the cables from the servo and it should not throw any codes as the servo will continue to act as normal, only its not manipulating the valve, at least this is what i have read elsewhere and possibly about the previous 1X99,

as for the valve itself I am not sure how to get to it as I have not messed with the one on my bike as I am planning on making my own slipons this winter and don't care that the valve is there, but you should be able to rip/cut the valve out and replace it with a nut and bolt through the left over hole or what some did on the 1X99 was just drill the rivets out of the flapper piece and the arm that it was riveted to... but again i have not really looked into this exhaust..

But I would not undo the cables from the servo motor unless you have removed the valve as the valve is most likely spring closed and it would be closed at all times which is not good..

someone please correct me if I m wrong or misleading here..

Removing the cables and keeping the valve in place will still throw an error code.
CRAZYDUC996 likes this.
MotomillioN is offline  
post #7 of 15 (permalink) Old 08-16-2018, 04:11 PM
Senior Member
 
Join Date: Jun 2018
Posts: 177
Don't know but my V4S threw an error code @ 2k miles w/ the ex valve servo... luckily got it into the shop same day and initially they couldn't figure it out but after some battery pulls apparently it cleared lol; took them like 2 hours
playersnoopy is online now  
post #8 of 15 (permalink) Old 08-20-2018, 04:48 AM
Member
 
Join Date: Mar 2018
Location: New Zealand
Posts: 86
Mine is still attached but no cables no hazard on the dash but unplug it and it does show a hazard symbol bottom rh side
so left it plugged till some one does an electrical disable
Beaker is offline  
post #9 of 15 (permalink) Old 08-20-2018, 10:27 AM
Junior Member
 
Join Date: Jul 2018
Posts: 28
V4 Exaust Eliminator Healtech ESE-D03 - Ducati Forum

this guy installed a servo eliminator...
bisogna likes this.
CRAZYDUC996 is offline  
post #10 of 15 (permalink) Old 08-21-2018, 11:06 AM
Senior Member
 
German4rings's Avatar
 
Join Date: Apr 2018
Posts: 107
Garage
Whats the purpose of this ? To get the exhaust to stay open ? Is it a noise thing ? Or power ?

grip bars , grab throttle and twist !
German4rings is offline  
Reply

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome